Dyson vacuum cleaners are a lifesavers. It is quality equipment that can clean up some of the toughest messes. However, most of them aren’t cheap. A Dyson vacuum’s lifespan depends on how well it’s taken care of and how often it’s cleaned. Vacuums are often overlooked by many people who assume that the tool itself is capable of cleaning up messes.
You can keep its suction power strong by taking care of the filter and cleaning it regularly. You don’t know where to start? Don’t worry! This is the ultimate guide on how to clean Dyson vacuum.
How To Clean Dyson Vacuum (Step By Step)
Various Dyson vacuum cleaner models are available on the market. The most common models will be discussed so you feel confident you are doing the job correctly. Most models require the same cleaning process.
Go through the guide to learn how to clean Dyson vacuums. Let’s get started!
If you are facing charging issues with your Shark Robot vacuum, read this Shark Robot Vacuum Not Charging (100% Problem Solved)
Basic Steps To Clean Dyson Vacuums
Let’s start with general instructions and then address any model differences individually. There are usually noticeable differences between models, but it’s worth discussing after this.
What You Need:
- A bucket of water
- Microfiber cloth
- A sponge with a handle to reach difficult places
- Use mild dish detergent as a light cleaning solution.
Read this guide if you are looking for a solution for Shark Vacuum Brush Not Spinning (Causes and Easy Fixes)
How To Clean Dyson Vacuum ( Easy Steps)
- The first step is to unplug your vacuum. When it is on, it could stir up dust, or if it comes in contact with water, it poses a safety risk.
- Dyons are bagless, so you’ll empty the canister in the same way you would when it’s full. To prevent dust particles from flying everywhere, safely dispose of them outside or in the trash. There are different methods for different types of models, which will be addressed in each section below. If you are not sure because it is your first time, consult the manual.
- Then, mix your light detergent with your bucket of water once the canister is empty. You don’t want the plastic or materials to melt, so the water should be mild or warm but not hot. To kill bacteria, warm is better than cold.
| Tip: Try this DIY natural cleaning solution. Mix white distilled vinegar with water! This can be used to clean bathrooms, glass, and more! |
- Take your sponge and squeeze out any excess water. There is no need to fill up the inside with too much wetness or soap. Use a non-shedding microfiber to wipe it down again after a good wipe down.
- While we work on the filter, set aside your canister to dry completely.
Read this if you are looking for information on How to Reset Shark ION Robot. (2 Easy Methods)
How to clean Dyson Vacuum hose head?
If you’re wondering how to clean Dyson vacuum cleaner hose, then you’re in the right place. There are a few simple steps in this process. Use a microfiber cloth to wipe down the exterior. Keeping the inside of the hose clean is optional since the vacuum motor moves particles along with a lot of air.
You should only worry about major blockages if you vacuumed up something that wasn’t supposed to be vacuumed, such as change or larger items. You should only vacuum pet hair, dust, and debris, while larger items should be picked up by hand, according to your manual. Bed bugs should never be cleaned up with a vacuum.
Read this if you are looking for information about Shark Vacuum Troubleshooting (5 Easy Tips For Shark Vacuums)
How to clean Dyson vacuum filter?
The Dyson vacuum filter is arguably its most important part, so let’s begin with it after the canister. It is easy for filters to become clogged if not taken care of, which can cause your motor and power to suffer. Their job is to prevent particles from returning to their air. However, too much buildup is not a good thing. For more information, Read this, Â How to Clean Dyson Filter (8 Easy Steps)
What You Need:
- A sink
- Non-shedding microfiber cloth
How To Clean Dyson Canister Filter?
Follow these simple steps to clean Dyson canister filter:
- Filters will be differentiated based on their model below. Note: Some Dyson models may have the filter in different places or have 2 filters. Make sure you remove it correctly regardless of the instructions in your manual.
- Head outside with the filter alone to remove dust and gently shake or tape it. While removing all the dust is impossible, getting the loose particles out is important.
- After that, you should bring it inside and run it under cool water. Avoid using hot water. You don’t need to worry about using soap. These Filters, like cheese graters, contain tiny pores to trap dirt and debris. You can get the rest with a simple rinse. You can use your hand to softly manipulate any noticeable blocks. Don’t press too hard with your hands.
- To remove the debris, fill the filter with water (some of it will seep) and shake it before setting it aside to dry.
- Place a microfiber cloth over it and let it air dry. Placing it safely will prevent it from falling and denting. Any dents will require a replacement since they will prevent it from functioning correctly.
What is the Easy way to clean Dyson vacuum head?
Cleaning your Dyson vacuum may be one of the most unpleasant things you ever do. It’s a must since things can get tangled.
What You Need:
- Nail scissors
- Screwdriver
- Microfiber cloth
How to clean Dyson vacuum head (Step By Step)
Follow these easy steps to clean Dyson vacuum head:
- Turn the vacuum over and carefully clip any entangled hairs. The vacuum can be damaged if you pull them out by hand beforehand.
- Also, be very careful not to cut into the bristles of the brush. The result will be a complete replacement.
- You may need to use a screwdriver and lift the protector plate to access the brush roll. It’s more complicated than it may seem, but reading the manual is always a good idea.
- You can wipe down the sole plate with a microfiber cloth if you detach it.
It’s done! That is how to clean Dyson vacuum head. It’s also a good idea to wipe down the entire outside perimeter with a cloth. Now, let’s look at some of the models.
How to clean Dyson cordless vacuum:
In cordless Dyson vacuums, the filter is near the end of the handle rather than the bottom. Some upright models have two filters, one at the top and one at the bottom. The main difference is how Dyson stick vacuums are cleaned.
Here’s what you need to know:
- How to clean dyson vacuum v8?
- How to clean dyson vacuum V11 ?
For these vacuums, you can follow the same instructions. They are also slightly different cordless vacuum models. The differences between them are in their features, not necessarily in how they clean.
How to clean a Dyson Ball vacuum?
There is no difference in how to clean a Dyson Ball Vacuum or a Dyson animal vacuum cleaner. When cleaning these vacuums, lay them on their side as you follow the steps above. Red attachments and knobs indicate that you can remove them for easier cleaning. A stick vacuum’s filter looks like a circular disk, while an animal vacuum’s looks like a circular disk.
How to clean a Dyson Cyclone?
Another cordless Dyson vacuum is the Dyson Cyclone. It has a red trigger near the handle that you can press to detach the filter and canister instead of manually removing it. When you are ready to detach the vacuum, press this button. If you Do this unexpectedly, it can result in the vacuum falling.
How to clean Dyson vacuum v7?
The V7 is also a cordless Dyson, but the filter differs slightly. The motorhead is thicker, and the filter sits on top. It is probably purple and sits in the middle of the head. It looks like an elongated ice cream cone when you pull it out with your hand.
Conclusion
Finally, knowing how to clean Dyson vacuum is important for protecting your investment.
The job should be done every two months (or more often, if necessary) and with the right supplies. For further information contact Dyson Customer Support.
Frequently Asked Questions
- Why should I clean my Dyson vacuum?
Maintaining your Dyson vacuum will ensure it works properly and lasts long.
Keeping your machine clean is important because dirt, dust, debris, and pet hair can build up over time and clog up parts. As a result, its suction power decreases.
- Can I clean my Dyson vacuum inside?
No, you cannot clean Dyson vacuum’s inside. Filters and brush bars are the only parts that can be safely cleaned. If you are not experienced with disassembling anything else, it is not recommended to do so.
- How to get a Dyson filter out?
Dyson filters can be removed by removing the cyclone part of the vacuum. At the bottom, the filters are easily accessible and easy to replace.
- Can I clean a Dyson vacuum with bleach?
It is never a good idea to clean a Dyson vacuum with bleach. Plastic parts and filters can be damaged, rendering them ineffective. Use only dish detergent and water – or compressed air if necessary.